|
Nominal chemical composition % (to EN 573-1):
|
|
Si
|
Fe
|
Cu
|
Mn
|
Mg
|
Cr
|
Zn
|
Ti
|
Others
|
Al
|
| Each |
Total |
| 0,3-0,6 |
0,1-0,3 |
0,1 |
0,1 |
0,35-0,6 |
0,05 |
0,15
|
0,1 |
0,05
|
0,15
|
Remainder |
|
|
Typical mechanical properties:
|
|
Bars drawn (to EN 754-2):
|
|
Temper
|
Dimensions (mm)
|
Rm( MPa)
|
Rp0,2 (MPa)
|
A %
|
A50 %
|
|
Diam
|
Flat bar
|
mini
|
mini
|
mini
|
mini
|
|
T4
|
<80
|
<80
|
130
|
65
|
15
|
13
|
|
T6
|
<80
|
<80
|
215
|
160
|
12
|
10
|
|
|
Tubes drawn (to EN 754-2):
|
|
Temper
|
Epaisseur paroi
|
Rm( MPa)
|
Rp0,2 (MPa)
|
A %
|
A50 %
|
|
mm
|
mini
|
mini
|
mini
|
mini
|
|
T4
|
|
|
|
|
|
|
T6
|
<20
|
215
|
160
|
12
|
10
|
|
|
Bars extruded (to EN 755-2):
|
|
Temper
|
Dimensions mm
|
Rm (MPa)
|
Rp0,2 (MPa)
|
A % mini
|
A50 % mini
|
|
Diam (D)
|
across flats or thickness (S)
|
mini
|
max
|
mini
|
max
|
|
T4
|
£ 150
|
£ 150
|
120
|
-
|
60
|
-
|
16
|
14
|
|
T5
|
£ 150
|
£ 150
|
160
|
-
|
120
|
-
|
8
|
6
|
|
T6
|
£ 150
|
£ 150
|
190
|
-
|
150
|
-
|
8
|
6
|
|
T64
|
£ 50
|
£ 50
|
180
|
-
|
120
|
-
|
12
|
10
|
|
T66
|
£ 150
|
£ 150
|
215
|
-
|
160
|
-
|
8
|
6
|
|
|
Tubes extruded (to EN-755-2) :
|
|
Temper
|
Dimensions mm
Wall thickness
|
Rm (MPa)
|
Rp0,2 (MPa)
|
A % mini
|
A50 % mini
|
|
mini
|
max
|
mini
|
max
|
|
T4
|
£ 15
|
120
|
-
|
60
|
-
|
16
|
14
|
|
T5
|
£ 15
|
160
|
-
|
120
|
-
|
8
|
6
|
|
T6
|
£ 15
|
190
|
-
|
150
|
-
|
8
|
6
|
|
T64
|
£ 15
|
180
|
-
|
120
|
-
|
12
|
10
|
|
T66
|
£ 15
|
215
|
-
|
160
|
-
|
8
|
6
|
|
|
Profiles extruded (to EN 755-2):
|
|
Temper
|
Dimensions
|
Rm( MPa)
|
Rp0,2 (MPa)
|
A %
|
A50 %
|
|
mm
|
mini
|
mini
|
mini
|
mini
|
|
T4
|
£ 25
|
120
|
60
|
16
|
14
|
|
T5
|
£ 5
5<e£ 25
|
160
140
|
120
100
|
8
8
|
6
6
|
|
T6
|
£ 3
3<e£ 25
|
190
170
|
150
140
|
8
8
|
6
6
|
|
T64
|
£15
|
180
|
120
|
12
|
10
|
|
T66
|
£ 3
3<e£ 25
|
215
185
|
160
150
|
8
8
|
6
6
|
|
|
Wire (to EN 1301-2):
|
|
Temper
|
Diameter up to and including
|
Rm (MPa)
|
|
A100 m % typique
|
|
mini
|
max
|
|
T39
|
³ 6
|
220
|
-
|
-
|
-
|
|
T39
|
< 6
|
270
|
-
|
-
|
-
|
|
T4
|
£ 20
|
140
|
-
|
90
|
13
|
|
T6
|
£ 20
|
210
|
-
|
160
|
-
|
|
T89
|
< 6
|
260
|
-
|
-
|
-
|
|
|
Properties (for guidance only):
|
|
Corrosion:
|
| General corrosion rating |
Very good
|
| Corrosion in industrial atmosphere |
Good
|
| Corrosion in marine atmosphere |
Good
|
| Corrosion in rural atmosphere |
Very good
|
| Stress corrosion |
Very good
|
| Exfoliation rating |
Very good
|
| Intergranular corrosion |
Very good
|
| Pitting rating |
Good
|
|
|
Anodising:
|
| Bright anodising |
Good
|
| Colour anodising |
Very good
|
| Hard anodising |
Very good
|
| Protective anodising |
Very good
|
|
|
Forming, machining:
|
| |
T5
|
| Cold forming |
Good
|
| Deep drawing |
Good
|
| Stretch forming |
Not recommended
|
| Spinning ability |
Good
|
| Extrudability |
Excellent
|
| Machinability |
Acceptable
|
|
|
Welding:
|
| Electron beam welding |
Good
|
| Gas welding |
Good
|
| Arc welding |
Very good
|
| Spot welding |
Good
|
| Brazing |
Very good
|
| Soft soldering |
Good
|
|
|
Physical and elastic properties:
|
|
Temper
|
Elastic
|
Physiques
|
| |
E
|
G
|
n
|
Tsol
|
Tliq
|
Cp
|
a
|
r
|
rel
|
l
|
EC
|
|
MPa
|
MPa
|
-
|
°C
|
°C
|
J kg-1 K-1
|
µm m-1 K-1
|
kg m-3
|
nW m
|
W m-1 K-1
|
%IACS
|
|
T5
|
69500
|
26100
|
0.33
|
610
|
655
|
898
|
23.4
|
2700
|
32
|
209
|
54
|
|
| Key: |
|
E
|
Modulus of elasticity |
MPa |
|
G
|
Modulus of rigidity |
MPa |
|
n
|
Poisson's ratio |
|
|
Tsol
|
Solidus temperature |
°C |
|
Tliq
|
Melting temperature |
°C |
|
Cp
|
Specific heat |
J kg-1 K-1 |
|
a
|
Coefficient of thermal expansion |
µm m-1 K-1 |
|
r
|
Density |
kg m-3 |
|
rel
|
Resistivity |
nW m |
|
l
|
Thermal conductivity |
W m-1 K-1 |
|
EC
|
Electrical conductivity |
%IACS |
|